AC Repair
in Galveston, IN
When an AC system in Galveston runs through long cycles without bringing the temperature down, blows air that does not feel cold, starts and shuts off before completing a full cooling cycle, or shows signs of water near the indoor unit or ice on the refrigerant lines — those are symptoms that deserve a diagnostic visit rather than a reset and a wait. Kokomo AC Repair provides residential AC repair for Galveston homes, starting with understanding what the system is actually doing before deciding how to correct it.
Warm air, weak cooling, short cycling, water, ice, and unclear AC problems diagnosed for Galveston homes.
Diagnose What The AC Is Actually Doing
Warm vents, weak airflow, early shutoffs, moisture — AC repair starts with identifying what the system is showing before settling on a fix.
Local AC Repair
for Galveston Homes
For homeowners in Galveston, Indiana dealing with a central AC system that runs without lowering the indoor temperature, vents that push warm or noticeably weak airflow, an outdoor unit that does not respond when the thermostat calls for cooling, water appearing near the indoor air handler, ice or frost on the refrigerant lines, or a system that starts and stops in short bursts — AC repair in Galveston through Kokomo AC Repair starts by reviewing what the system is actually doing rather than defaulting to the most expensive path before the problem is understood.
Cooling Drops During Warm Weather
When an AC system runs consistently through warm afternoons but the indoor temperature barely changes — or drops a few degrees and then climbs back — the system is running without producing the output it should. That gap between effort and result can come from a restricted coil, a refrigerant concern, outdoor unit behavior under load, or airflow that is not reaching the supply vents effectively. Each of those has a different repair path.
AC Runs But The House Stays Warm
Longer cooling cycles that do not move the home to the thermostat setting, supply air that feels only slightly cooler than ambient room temperature, or one area of the house that never quite catches up — these symptoms are worth diagnosing correctly rather than attributing to the weather alone. The right description of what the system is doing, and when, helps narrow the cause faster than a general service call without a clear starting point.
Repair First, Replacement Only When Needed
A lot of AC problems that show up as poor cooling or unusual system behavior have specific, isolated causes — blocked drainage, a failing contactor, a dirty evaporator coil, or a thermostat that has drifted out of calibration. None of those require replacement. The repair-versus-replacement conversation belongs after the diagnostic shows what is actually wrong, not before it.
Focused On The Cooling Problem
AC repair decisions are clearest when they start with the specific symptom — warm air from the vents, weak airflow, short cycling, water near the indoor unit, ice on the refrigerant lines, an outdoor unit that will not start, or a thermostat that is not triggering cooling. Each of those points toward a different part of the system and a different repair category, and understanding which one applies saves time and money.
Signs You Need AC Repair
in Galveston
AC problems do not always mean the system has completely stopped. More often, there is a sign first — air that feels slightly too warm, a house that takes twice as long to cool down as it used to, moisture collecting somewhere it should not be, or an outdoor unit sitting quiet while the indoor blower runs. Those early signals are worth paying attention to before the issue gets harder to isolate.
What The AC Is Showing You
The clearest indication that an AC repair is needed usually starts inside the home — supply air that does not feel cold enough, a room that never settles to the thermostat setting, a puddle forming under the air handler, frost on the copper lines coming off the indoor coil, or the system turning itself off after only a few minutes of running. The outdoor unit is another telling point: if the indoor blower is moving air but the outside unit is not running, the system is only doing half its job.
-
Warm Air From Vents
The air is moving, but it does not feel cool — or it feels like it is only a few degrees below room temperature rather than cold. The system may be running a full cycle without the refrigerant side doing its part, or the coil condition has changed enough that the air is not picking up the cooling it should.
-
Weak Cooling Or Long Run Times
If the system runs two or three hours during the afternoon and the indoor temperature barely drops, something is limiting its output. That could be an airflow restriction, a component not performing the way it should, or a capacity issue tied to how the system is operating — not necessarily how it was designed.
-
AC Starts And Stops Often
Short cycling — where the AC kicks on, runs for a minute or two, then shuts off before completing a full cooling cycle — can have several causes. An overheating issue, a control problem, an electrical concern, or restricted airflow can all trigger it. What they share is that repeated short cycles tend to make the underlying issue worse, not better.
-
Water Or Ice Near The AC
Water pooling under the indoor unit usually points to a blocked condensate drain. Ice on the refrigerant lines is a different kind of signal — it can come from restricted airflow, a dirty evaporator coil, or a refrigerant concern. Either way, continuing to run the system when ice is forming is not a solution.
-
Outdoor Unit Does Not Respond
The indoor blower runs and air moves through the vents, but the outdoor condenser unit is not turning on — or it hums briefly and shuts off. Without the outdoor unit running, the system has no way to reject the heat it is pulling from the home. The cause could be electrical, mechanical, or a safety shutoff that has tripped for a reason worth finding.
-
Thermostat Does Not Match The Room
The thermostat is set to 72, but the room holds at 80 and the system does not seem to be responding to the gap. Sometimes the issue is the thermostat itself. More often it is the cooling system not producing what the thermostat is calling for — and in either case, the thermostat reading alone does not tell you which side of the system is falling short.
A Small Cooling Change Can Still Be A Repair Signal
If one of these symptoms has shown up more than once, feels worse than it did a few weeks ago, or consistently appears during the warmer parts of the day, the system is probably showing a pattern rather than a one-off event. That pattern is worth a diagnostic visit — it tends to narrow the cause faster and more accurately than waiting to see if the problem resolves on its own.
How We Diagnose
AC Repair Problems
Two homes can describe the same symptom — warm air from the vents — and end up with two different repair needs. One might have a frozen coil from a blocked filter; the other might have a failing capacitor that is not letting the outdoor unit start. Finding the actual cause is what makes a repair fix the problem instead of just delaying it.
Start With The Cooling Complaint
What the homeowner notices first is usually the best starting point — air that feels warm, a blower that runs but does not seem to be doing anything, water near the air handler, ice on the lines, or an outside unit that is oddly quiet. That starting observation shapes which parts of the system get checked first, and in what order, rather than working through an identical checklist regardless of what the home is showing.
-
01
Thermostat Response
Before assuming the equipment itself has a problem, the thermostat is checked first — mode, set temperature, the temperature it is reading, and whether it is actually sending a call for cooling to the air handler and outdoor unit. A misconfigured or drift-affected thermostat can mimic several different AC problems.
-
02
Filter And Return Air
A heavily loaded filter restricts the air the system pulls in, which reduces cooling output and can cause the evaporator coil to ice over. It is quick to check and, when it is the issue, cheap to resolve — but it can make other parts of the system look like they are failing when the airflow restriction is the underlying cause.
-
03
Indoor Coil Condition
The evaporator coil is where the cooling actually happens. A coil that is dirty, partially blocked, or showing ice buildup is not going to transfer heat out of the air the way a clean coil does. Ice formation on the coil or lines is also a sign the system has been running under restricted airflow or with a refrigerant-related issue that has been developing over time.
-
04
Drain Line And Moisture
Water pooling near the indoor unit most often means the condensate drain is blocked — which happens as algae or debris builds up in the drain pan or line. Left alone, it can overflow and cause water damage. It can also trigger a float safety switch that shuts the system down, which may be why the AC seems to stop for no obvious reason.
-
05
Outdoor Unit Operation
When the indoor air handler is running but the house is not cooling, the outdoor condenser unit is worth checking closely. A unit that hums but does not start may have a failed capacitor. A unit that is completely silent may have a tripped safety, a contactor issue, or an electrical disconnect problem. In either case, the indoor unit cannot cool the home on its own.
-
06
Electrical And Control Parts
Capacitors, contactors, wiring connections, safety switches, and control boards can all cause symptoms that look like the AC itself has failed. A capacitor that has weakened will still allow the unit to start sometimes — which is why these problems often appear inconsistently before they become persistent. Breaker trips after starting are another signal worth tracing carefully.
-
07
Cooling Output And Run Cycle
Once the individual components have been reviewed, the system's overall performance is worth looking at — how long it runs to bring the home to the set temperature, how far it gets, and whether any performance signs suggest the issue is specific and repairable or reflects a pattern that points to the equipment being past its useful service life for the home it is serving.
Why Guessing Can Waste Time
Weak cooling alone could be airflow restriction, a dirty coil, an outdoor unit that is not running at full capacity, a refrigerant-related performance loss, or an electrical component that is starting to fail. Each of those has a different repair. Deciding which one it is before checking means either fixing something that was not the problem or ordering a part the system did not need — either way, the real issue stays unfixed.
Common AC Problems
We Repair
Central AC repair problems tend to show up in a handful of recognizable ways — the system runs but the house does not cool, something is dripping or frozen around the equipment, the outdoor unit will not start, or the system keeps cutting out. Identifying which of those fits the situation is usually the first step toward understanding what needs to be fixed.
Match The Problem To The Repair Review
Visible symptoms do not always make the cause obvious. Warm air might come from a dirty coil, a refrigerant-related performance loss, or an outdoor unit that is not running. Water near the unit might be a blocked drain or a freezing and thawing cycle tied to airflow restriction. Short cycling might be an overheating issue, a control problem, or an electrical part that is beginning to fail. The table below matches what homeowners typically see with what usually needs to be checked.
| AC Problem | What You May Notice | What May Need Review |
|---|---|---|
|
AC blowing warm air
|
Airflow from the vents is present, but the air does not feel cold enough to actually pull the room temperature down. | Cooling output, indoor coil condition, outdoor unit operation, thermostat response, and refrigerant-related performance signs. |
|
AC running constantly
|
The system runs for very long stretches — hours at a time — but the home never seems to reach the thermostat setting. | Filter and coil condition, airflow, outdoor unit performance, and whether something is limiting the system's ability to complete a normal cycle. |
|
AC not turning on
|
The thermostat is calling for cooling but nothing happens — or only the indoor air handler responds while the outdoor unit stays off. | Thermostat signal, capacitor, contactor, wiring connections, safety switches, and breaker or disconnect behavior. |
|
AC short cycling
|
The system starts, runs briefly — sometimes only two or three minutes — then shuts off, only to start again shortly after. | Airflow restriction, control behavior, overheating triggers, electrical component condition, and coil condition. |
|
AC leaking water
|
Water collects near the indoor unit, around the drain pan area, or on nearby flooring. | Condensate drain and pan condition, freezing and thawing patterns, coil condition, and whether restricted airflow is causing ice to form and melt. |
|
Frozen coil or ice buildup
|
Ice appears on refrigerant lines, coil surfaces, or equipment surfaces — sometimes alongside weak airflow or a noticeable drop in cooling. | Filter, return airflow, indoor coil condition, blower operation, and refrigerant-related performance signs that may explain why ice is forming. |
|
Outdoor unit not running
|
The indoor blower moves air normally, but the outdoor condenser unit stays silent, hums without starting, or cuts off quickly after attempting to start. | Capacitor, contactor, power supply, outdoor fan motor, wiring, and the control signal coming from the thermostat and air handler. |
|
Weak airflow from vents
|
Some vents produce noticeably less air movement than others, or the overall airflow from the system feels lower than normal. | Filter and return air condition, blower performance, whether the coil has buildup affecting airflow, and the overall air path through the system. |
|
Breaker trips when AC starts
|
The breaker trips when the AC starts up, or trips again after being reset — sometimes after a short period of operation, sometimes on the first attempt. | Electrical load at startup, capacitor condition, compressor startup behavior, contactor, and wiring — not a problem to reset and ignore repeatedly. |
The Same Problem Can Have More Than One Cause
Weak cooling, for example, can come from restricted airflow, coil condition, outdoor unit performance, an electrical component that is not functioning properly, or a refrigerant-related performance issue. The visible problem points toward a category of checks, not a specific fix — which is why the repair decision should follow what the system shows during review rather than what the symptom alone suggests.
Emergency AC Repair
in Galveston
When the central AC stops cooling during a hot stretch, will not start back up, keeps shutting off before completing a cycle, trips the breaker, or shows water, ice, or unusual electrical behavior — those are the situations where emergency AC repair makes sense over waiting for a standard appointment. The system should be looked at rather than repeatedly restarted, especially when the same problem keeps coming back each time.
When Cooling Should Not Be Pushed
An AC that runs for a few minutes and then shuts off, restarts, and shuts off again is showing a pattern — not a one-time glitch. Each restart attempt when the underlying cause has not been addressed can add strain to the components involved. The same applies to a breaker that trips when the AC starts: resetting it once is a reasonable first check, but if it trips again immediately, the circuit or equipment needs a closer look before the next attempt. Water around the indoor unit or ice on the refrigerant lines also both tell you the system should not just keep running.
| Urgent AC Sign | Why It Needs Attention |
|---|---|
|
AC stops cooling during hot weather
|
The system may still be running — fan moving, unit cycling — but cooling output has dropped to where the home temperature is rising rather than holding. That combination, especially during a heat stretch, should be checked rather than assumed to be a temporary issue. |
|
System will not restart
|
When the thermostat is correctly set to cooling and nothing happens — no response from the indoor unit or the outdoor unit — there is likely an electrical, control, or safety issue involved. The cause could be a safety switch that tripped for a reason, a power issue, or a component that has failed. |
|
AC shuts down repeatedly
|
Repeated shutoffs — whether the system trips a safety, stops mid-cycle, or simply turns off before the home cools — often reflect overheating, drainage trouble, restricted airflow, or an electrical component that is not operating correctly. The pattern matters more than any single shutdown. |
|
Breaker trips when AC starts
|
A breaker that trips on the first AC startup, or trips again immediately after a reset, should not be kept reset. The trip may be protecting against an electrical problem — a startup load issue, a failing component drawing excess current, or a wiring concern — and resetting it repeatedly without finding the cause is not safe practice. |
|
Water or ice near the system
|
Water pooling under the indoor unit or ice on the refrigerant lines both signal that something in the system's operation is off — whether drainage, airflow, coil condition, or a refrigerant-related issue. Running the system through those conditions does not make them resolve and may make the effects worse. |
|
Burning odor, buzzing, or unsafe behavior
|
An unusual smell from the equipment — hot or burning — alongside buzzing from the air handler or outdoor unit, or any behavior that looks or sounds like an electrical problem, should be taken seriously. These signs are not something to work around by checking whether the AC starts again. |
Stop Restarting If This Happens
- The breaker trips again after being reset once
- The AC starts and shuts down repeatedly without completing a normal cycle
- Burning odors, smoke, buzzing, or any unsafe electrical behavior appears
- Water or ice keeps forming around indoor equipment each time the system runs
- The outdoor unit will not respond correctly even after checking the thermostat setting
Safety note: If you notice smoke, burning odors, or unsafe electrical behavior from the AC system, stop using the equipment and seek appropriate professional help before attempting to restart it.
For cooling failures that should be reviewed before another restart attempt.
AC Repair or
AC Replacement?
Not every AC problem is a signal that it is time to replace the system. A lot of cooling issues are specific and repairable, and the right repair can restore normal operation without a major expense. That said, a pattern of returning problems, a system that does not improve after service, or a repair cost that no longer makes sense given the equipment's condition are all worth considering honestly before choosing the next step.
Start With The Repair Findings
The decision between repair and replacement should come from what the diagnostic actually shows — not from what the symptom looks like before the system is reviewed. An isolated failed capacitor is very different from a compressor that has been struggling through repeated service calls for two summers. Whether the issue is repairable, whether performance returns after repair, how often problems have been coming back, and what the overall condition of the equipment is will all shape the answer more accurately than the symptom alone.
Repair May Make Sense When
-
The fault is isolated
A specific part — a capacitor, a contactor, a blocked drain, a refrigerant-related adjustment — has failed while the rest of the system is in reasonable condition. That kind of repair tends to restore normal operation without a larger conversation.
-
Service history is clean
The system has not required repeated calls over the past couple of seasons. A first or second repair on equipment that has otherwise operated without issues is usually worth doing.
-
Cooling improves after repair
When a repair addresses the actual cause and the system returns to performing the way it should, that is a good indicator the equipment still has useful service life.
-
Repair cost is proportionate
The repair cost is a reasonable fraction of what the equipment is still worth to the household. A few hundred dollars on a system that is otherwise running well is a different calculation than the same amount on a system with multiple failing components.
-
The system still cools after service
After a repair visit, the system settles back into normal cycles and maintains the thermostat setting. That is the result the repair was intended to produce, and it is a reasonable way to evaluate whether it worked.
Replacement May Be Worth Discussing When
-
Repairs keep coming back
When the same issue, or a new one, returns within a season or two of a previous repair, the pattern is telling you something about the overall state of the equipment that a single repair may not be able to fix on a lasting basis.
-
Cooling keeps declining
If cooling performance has dropped from one summer to the next even with service, the system may be losing capacity in ways that individual repairs are not addressing.
-
The system struggles even after service
When a repair has been done correctly but the home still does not cool the way it should, the issue may not be a single repairable fault — it may reflect equipment that is no longer able to serve the space reliably.
-
Repair cost outpaces system value
When a major repair — compressor work, refrigerant system work, multiple simultaneous component failures — costs more than the system is practically worth for the years of service it has left, AC installation planning becomes a more reasonable conversation to have.
-
The equipment is no longer practical to rely on
Not every old system is a replacement candidate, but a system that has reached a point where its condition is too unpredictable to plan around may make a replacement conversation worth having before the next summer season.
The Goal Is The Right Cooling Decision
The answer to repair or replace should come from the system's actual condition: what the diagnostic shows, how the equipment has performed over time, whether repairs have been holding, and whether the problem is the kind that can be fixed and stay fixed. A decision made from those facts is more likely to be the right one than a decision made from the symptom alone.
What's the Average
AC Repair Cost?
AC repair cost is not a single number — it moves based on what the problem actually is, how much of the system needs to be reviewed, what parts are involved, and whether the repair is a straightforward fix or part of a larger pattern of service calls. A quick drain clearing and a failed compressor are both "AC repair," but they are very different service visits.
Repair Scope Changes The Price
A diagnostic visit to identify why the AC is not performing is a different scope than correcting a small control issue, resolving an electrical component failure, addressing drainage or ice buildup, or working through a system that has had repeated cooling problems. Each step up in scope changes what the visit involves and how long it takes, which is why actual pricing should be confirmed after the system is reviewed — not quoted before anyone has seen it.
Whether the issue is warm air, no cooling, short cycling, water, ice, or a startup problem shapes where the diagnostic and repair effort starts.
Some repairs involve smaller, commonly stocked components; others involve larger or less common parts that affect both cost and how long the repair takes.
Thermostat behavior, capacitor condition, contactor operation, wiring connections, and breaker behavior can all require different levels of review before the issue is resolved.
Water near the unit, clogged drain lines, ice buildup, or freeze-thaw patterns can change what the repair involves and how much of the system needs attention.
Outdoor unit condition, clearance, wiring access, and what needs to be reviewed or replaced can affect how straightforward the repair visit is.
Repeated service needs over one or two seasons can change what the repair conversation looks like — a pattern of returns is a different scope than a first service call.
Only when inspection shows that the repair cost no longer makes sense for the system's condition does a replacement conversation become part of the visit.
*Average ranges are general estimates only. Actual pricing should be confirmed after the AC system and repair scope are reviewed.
Why Galveston Homeowners
Choose Kokomo AC Repair for AC Repair
AC repair does not benefit from guessing. The same symptom — weak cooling, short cycling, an outdoor unit that will not start — can come from several different places in the system, and the repair direction should follow what is actually found during review. Kokomo AC Repair approaches every cooling problem by first understanding what the system is showing rather than defaulting to the most expensive or most familiar explanation.
Diagnosis Before Big Decisions
A weak-cooling complaint can trace back to airflow restriction, a coil that has accumulated buildup, a capacitor that is no longer holding charge, or a refrigerant-related loss — and each of those has a different repair. Pointing to the most visible or most expensive explanation before any of those are checked is how homeowners end up paying for work that does not address the actual issue. The diagnostic finding is what should drive the repair recommendation, not the symptom description on the phone.
| What The Repair Approach Should Consider | Why It Matters |
|---|---|
|
Cooling Symptom
|
Warm air, weak airflow, short cycling, water near the unit, ice on the lines, and outdoor unit trouble can each point to different parts of the system — which means the repair starting point is different in each case. |
|
AC Inspection When The Cause Is Unclear
|
AC inspectioncan help separate whether the cooling issue involves airflow, coil condition, drainage, thermostat response, outdoor unit behavior, or an electrical concern — so the repair addresses the right part of the system rather than a reasonable guess. |
|
Repair History
|
An AC that has been serviced multiple times in the past two seasons is telling a different story than one with a first isolated problem. The repair history shapes how the visit is approached and whether a larger conversation about the equipment's condition is warranted. |
|
AC Maintenance After Repeat Issues
|
AC maintenance can be useful when recurring cooling problems are tied to filter condition, coil buildup, drainage patterns, or seasonal operating concerns that a focused service visit can address before the next problem develops. |
|
Replacement Only When It Makes Sense
|
Replacement should not be the answer before the equipment has been properly reviewed. When repair cost, cooling performance, service frequency, and system condition together suggest that continued repair is no longer the practical path, that conversation belongs in the visit — but not before the system has been seen. |
A Repair Path Based On The AC Problem
The goal is to help homeowners understand whether the cooling issue calls for a focused repair, a closer inspection to find the cause, maintenance that may prevent the problem from returning, or a replacement conversation that is actually grounded in what the system shows. More about how service calls are approached is on our residential service approach page.
Focused On The Cooling Issue First
The service direction should come from what the AC system is actually doing and what the review finds — not from a predetermined answer that gets applied regardless of what the specific home and equipment are showing. That is the part of the repair approach that matters most for getting the problem resolved on the first visit.
Galveston
AC Repair FAQs
AC repair questions often start when the system keeps running but the house does not cool, when the unit starts and stops more than it should, when water shows up somewhere unexpected, or when the homeowner is not sure whether the issue needs a repair visit, a closer inspection, or a conversation about the equipment's overall condition.
Do you provide AC repair in Galveston, IN?
Service includes diagnosing and repairing warm air, weak cooling, short cycling, water or ice near the equipment, outdoor unit problems, thermostat response issues, and cooling concerns that have not been clearly explained by a previous visit. The goal is to find the cause before choosing the repair, not to apply a standard fix to a symptom description.
Why is my AC running but not cooling the house?
A system that runs continuously without lowering the indoor temperature might have a dirty coil limiting heat transfer, an outdoor unit that is not operating correctly, restricted return airflow, a thermostat that is not calibrated to the actual room conditions, or a refrigerant-related performance concern. Each of those looks like "AC running but not cooling" from inside the house, but each one is a different repair. A diagnostic visit that checks what the system is doing, not just what the homeowner reports, is usually the fastest path to finding out which applies.
What should I do if my AC keeps turning on and off?
Short cycling can come from airflow restriction, an overheating component triggering a safety shutoff, a control issue, an electrical part that is beginning to fail, or coil condition. Running the system through repeated short cycles does not fix any of those causes, and in some cases makes the component involved degrade faster. If the system keeps doing it after you check the thermostat setting and the filter, it should be reviewed by a technician rather than forced to keep running.
Is water near my indoor AC unit a repair issue?
The most common cause is a blocked condensate drain — algae or debris accumulates in the drain pan or line and prevents water from draining normally. But water can also appear because the system has been forming ice on the coil or refrigerant lines and then thawing when it shuts off — which points to a different issue involving airflow or operating conditions. Either way, the system running continuously while water is collecting nearby can make whatever problem is causing it worse, and can affect surrounding materials over time.
When should I choose AC inspection before repair?
If the same cooling problem has shown up more than once, or if you have been told the system needs replacement but are not sure whether that assessment is correct, an inspection gives you a clearer picture before you commit to either a repair or a larger decision. It can separate whether the concern is a specific repairable fault, a maintenance-related issue that has been building, a capacity concern, or an equipment condition question that changes the repair-versus-replacement conversation.
How do I know if AC replacement is better than repair?
Replacement becomes a more practical conversation when repairs keep returning, cooling performance has been declining even with service, or the repair cost is significant enough that it should be weighed against what the equipment realistically has left. If it turns out AC installation planning does make sense, that conversation should come from what the system shows during a review — not from the symptom alone, and not as a default answer before any inspection has been done.
What affects AC repair cost in Galveston?
A diagnostic visit to find out why the AC is not cooling is a different scope than replacing a capacitor, resolving a drainage or ice problem, or working through repeated failures that require more involved troubleshooting. The cost should be confirmed after the system is seen — not quoted over the phone based on a symptom description. To contact us and describe what the AC is doing, that is the best way to understand what a service visit for your situation would involve.
Schedule AC Repair
in Galveston, IN
If a Galveston home is dealing with warm air from the vents, an AC that runs without improving the temperature, short cycles that keep repeating, water or ice forming around the indoor unit, an outdoor unit that will not respond, or a cooling issue that came back after a previous service visit — Kokomo AC Repair can review what the system is showing and help identify the right repair direction.
Warm air, weak cooling, water, ice, short cycling, and unclear AC problems reviewed for Galveston homes.